Serviceability is available in Early Access Package (EAP): the feature is released with limits and usable, but only enabled on request while we collect feedback; it is not part of the current subscription and may become an additional subscription later.
Serviceability answers one daily question: "Is my runway lighting good enough for the CAT level it can be?" CORTEX Service calculates a serviceability verdict for every runway, landing direction and lighting function, based on the condition of each individual light.
1. Key concepts
|
Term |
Meaning |
|---|---|
|
Runway |
e.g. |
|
Landing direction (LD) |
One end of the runway, e.g. |
|
Function |
The role a light plays: Approach (High/Low Intensity), Threshold, Runway End, Touchdown Zone, Centreline, Edge, … A light can belong to several functions and landing directions at once (e.g. centreline and edge lights). |
|
CAT level |
The operating category of a landing direction: No CAT, CAT I or CAT II/III. Higher CAT levels require higher serviceability. |
|
Authority profile |
A set of thresholds per function and CAT level: FAA, ICAO, EASA, or Custom. |
|
Adjacency failure |
Two (or three, configurable) neighbouring unserviceable lights in the same function. This fails the function regardless of its overall percentage. |
2. How the verdict is calculated
Light → serviceable? (not faulty AND photometric OK, if enabled)
Function → % serviceable lights vs. profile threshold + adjacency check
Landing dir. → worst status of its functions
Runway → verdict per CAT level (No CAT / CAT I / CAT II/III)
A function is Unserviceable when its percentage drops below the serviceability threshold or an adjacency failure is detected. It shows a Warning when it is below the warning threshold.
3. Setup (administrators)
Step 1 — Assign functions to your lights
-
Select the lights on the map (lasso or multi-select).
-
Open Edit selected assets → Functions tab.
-
Choose the Type (function), Runway and Landing direction, then click + to add.
-
Click Update.
Tip: you can also fill the Function columns in the Excel asset import - here is an example file Functions Example file.xlsx
Here are the 13 CORTEX Service function codes:
|
Code |
Function |
Meaning |
In serviceability calculation |
|---|---|---|---|
|
APC (APP) |
Approach |
Approach lights in front of the runway. They guide the pilot towards the runway centreline. |
✅ Yes |
|
ASR |
Approach Side Row |
Red side-row barrettes on both sides of the approach centreline near the threshold. Only used on CAT II/III approaches. |
⏳ Later - To be included in APC for now |
|
PAP |
PAPI |
Precision Approach Path Indicator. A row of lights beside the runway that shows the pilot whether they are too high, too low or on the correct glide path. |
⏳ Later |
|
RCL |
Runway Centreline |
Lights along the runway centreline, used for guidance during take-off and landing in low visibility. |
✅ Yes |
|
RGL |
Runway Guard Lights |
Flashing yellow lights at runway holding positions that warn taxiing aircraft they are about to enter an active runway. |
⏳ Later |
|
RND |
Runway End |
Red lights across the far end of the runway that mark where the usable runway stops. |
✅ Yes |
|
RWE |
Runway Edge |
Lights along both edges of the runway that mark its width and length. |
✅ Yes |
|
STB |
Stop Bar |
A row of red lights across a taxiway at a holding position. Aircraft must not cross while the bar is lit. |
⏳ Later |
|
TCL |
Taxiway Centreline |
Green (or green/yellow) lights along the taxiway centreline that guide aircraft between the runway and the apron. |
✅ Yes |
|
TDZ |
Touchdown Zone |
Rows of white barrettes in the first part of the runway that show the pilot where to touch down. Required for CAT II/III. |
✅ Yes |
|
THR |
Threshold |
Green lights across the start of the runway that mark where the landing area begins. |
✅ Yes |
|
TWE |
Taxiway Edge |
Blue lights along the edges of taxiways and aprons. |
⏳ Later |
The calculation currently uses the 7 runway functions. Approach side row, PAPI, guard lights, stop bars and taxiway lights will be added in a later release. You can already assign these functions to your assets.
Some things are good to know:
-
One fixture can have two functions. A combined threshold/end light counts as THR for one landing direction and RND for the other, so it needs both functions assigned.
-
Not every function counts at every CAT level. RCL and TDZ only count towards serviceability at CAT II/III. For CAT I they aren’t required.
Step 2 — Configure serviceability
Go to Settings → Serviceability Configuration.
-
Contributors — choose which inputs count towards serviceability:
-
Faulty State — always on.
-
Photometric — optional. When off, photometric measurements are shown on the asset but not used in the calculation.
-
-
Authority profile — select FAA, ICAO or EASA. Serviceability thresholds and adjacent-failure limits are fixed for these profiles; the warning threshold can still be adjusted. Need different limits? Select Custom and start from the defaults.
-
Review the thresholds per CAT tab (No CAT / CAT I / CAT II/III):
ColumnMeaningServiceability thresholdBelow this % the function is unserviceableWarning thresholdBelow this % the function shows a warningAdjacent failuresNumber of consecutive unserviceable lights allowed (2 or 3)
-
Landing-direction assignments — set the Highest CAT each landing direction operates at (single select).
-
Click Save.
4. Daily use
Serviceability Cockpit
Open Cockpit → Serviceability. The overview tile shows how many landing directions meet their configured CAT.
-
Runway cards show a verdict per CAT level for the runway and each landing direction.
-
Click the number badge under a card to drill down: Runway → Landing direction → Function.
-
Function cards show the serviceability %, serviceable lights / total, and the cause: Faulty state, Photometric or Adjacency failure.
-
Use the map icon on any card to see those lights on the map, or the table icon to filter the table below.
Status legend: ❌ Unserviceable · ⬛ Unknown data · ⚠️ Warning · ✅ Serviceable · 📍 Adjacency failure
Grey “Unknown data” status — A grey square with a dash on a runway or landing-direction card means that the serviceability verdict for that CAT level cannot be calculated because the required lighting functions are not assigned to that runway or landing direction. Check the function assignments on the lights and assign the functions required for the affected CAT level (see Step 1 — Assign functions to your lights).
Lighting functions table — lists every function per landing direction with its CAT, input-module counts, serviceable assets, percentage, thresholds and current status. Filter by CAT, Runway, Landing direction, Function or Failed module.
Note: Shared asset filters do not apply to this cockpit. It always includes all assets in the calculation scope.
Asset details panel
For each light you now see:
-
Serviceability — overall status (Serviceable / Unserviceable / Adjacent Unserviceable), the Faulty toggle and the last photometric measurement.
-
Functions and adjacencies — the light's function, runway and landing direction, plus its neighbours (Primary / Opposite) with distance and bearing.
Map and filters
-
Adjacency failures are marked on the map with a red pin.
-
New filter sections:
-
Asset functions — No Function, By runway, By function.
-
Asset Serviceability — Serviceable, Unserviceable, Adjacent Unserviceable.
-
Cockpit → serviceability — show the assets that drive the serviceability cockpit.
-
5. Good to know
-
Lights without a function are not part of the calculation — use the No Function filter to find them.
-
Adjacency is based on light coordinates. Poor coordinates can cause wrong neighbours; check the Functions and adjacencies section on the asset.
-
Out of scope for now: compliance export (PDF/CSV) and serviceability alerts.